FS TraceyDevelopments Ltd Get a price
HomeServicesProjectsAboutContact

Service

Heritage & lime restoration

Lime render and mortar, rubble stone repair, brick arches and chimney work on older and protected buildings. Breathable build-ups, and no cement where it doesn’t belong.

Get a price

Old buildings were built to get wet and dry out again. Solid rubble stone walls have no cavity and no damp-proof course — they manage moisture by letting it move through the fabric and evaporate. Every decision on a period building follows from that one fact.

Why lime, and not cement

Cement render and cement pointing are hard, brittle and effectively vapour-closed. Applied to a solid stone wall, they trap moisture inside the fabric. The water then finds the softest route out, which is the stone itself — so the face of the stone spalls, the wall stays wet, and the damp shows up internally. Cement also cracks rather than flexes, and every crack lets water in behind a surface that won't let it out again.

Lime is softer than the stone around it, flexible enough to accommodate movement, and vapour-open. It sacrifices itself before the stone does. It's not nostalgia — it's the correct material for the wall.

What we do

  • Lime render, scratch coat through to finish coat, on stone and brick
  • Raking out cement pointing and repointing in lime mortar
  • Rubble stone repair, rebuilding and consolidation
  • Brick voussoir arches and reveal detailing
  • Chimney rebuilding and flaunching
  • Fireplace opening reinstatement and restoration
  • Internal lime plaster on solid walls

How we work

We match the mix to the wall rather than the other way round, taking account of the existing mortar, the exposure of the elevation and how hard the stone is. Renders go on in coats, each allowed to cure before the next, and lime needs protecting from sun, wind and frost while it carbonates. That is slower than cement and there is no way round it — a lime job pushed to a cement programme will fail.

Work on a protected structure, or on a building in an Architectural Conservation Area, normally requires planning permission even where the same work on an ordinary house would be exempt. Your local authority conservation officer is the first call, and getting them involved early usually makes the whole process easier.

Recent work

Lime render restoration to a house at Clogga, Co. Wicklow dating to around 1600, with the rubble stonework and a brick voussoir arch left exposed. A fireplace restoration in Bunclody, Co. Wexford, where old tongue-and-groove panelling was stripped back to reveal the original stonework, which was then re-pointed and plastered around a reinstated opening.

Photographs of both are on the projects page.

Common questions

Why can't I just use cement render on an old stone house?

Because a solid stone wall has no cavity and no damp-proof course, and relies on moisture evaporating back out through the wall. Cement is vapour-closed and traps that moisture inside the fabric, which then damages the stone itself and shows up as internal damp. Cement also cracks rather than flexing, letting water in behind a surface it can't get back out through.

Do I need planning permission for work on a protected structure?

Usually yes. Works to a protected structure that would materially affect its character generally require planning permission even where equivalent works to an ordinary house would be exempt, and buildings within an Architectural Conservation Area are subject to additional controls. Contact your local authority's conservation officer early, as they can often advise on an acceptable approach before you apply.

How long does lime take to cure?

Considerably longer than cement. Each coat needs time to cure before the next goes on, and the finished work needs protection from sun, wind and frost while it carbonates. This is why lime work is generally not carried out in hard frost, and why a lime programme cannot be compressed to match a cement one.

Can you match the existing mortar?

Yes. We look at the existing mortar, the hardness of the stone and how exposed the elevation is, and mix to suit. The aim is always a mortar softer than the stone around it.

Do you work on ordinary older houses, not just protected structures?

Yes. Plenty of pre-1940s houses have solid walls and the same physics apply, whether or not the building carries a formal designation.

Next step

Get a price on your job

Send us the address, what you're planning and any drawings you have. We'll come back with a realistic range before anyone spends time on a site visit.